L'Antre Du Protecteur (2020) Mac OS

Mini Solder Spool

L'antre Du Protecteur (2020) Mac Os X
L'antre Du Protecteur (2020) Mac Os Catalina

L'antre Du Protecteur (2020) Mac Os X

Soldering electronic components using a large solder spool of 454 grams or so is quite inconvenient even if it is mounted on a solder spool holder. I prefer to

Apple Mac mini MAC MINI Mini PC I5 8 Go 512 Go Mac OS Catalina Gris Intel Core i5, 3.0GHz, 8Go DDR4, 512Go SSD, Wi-Fi, Bluetooth 5.0, HDMI, Ethernet, Thunderbolt 3 x 4, USB 3.0 x 2, macOS 1 249, 20 €. Apple helps you keep your Mac secure with software updates. The best way to keep your Mac secure is to run the latest software. When new updates are available, macOS sends you a notification — or you can opt in to have updates installed automatically when your Mac is not in use. MacOS checks for new updates every day and starts applying them in the background, so it’s easier and faster.

Pull Handle

This is a simple pull handle. A #10 flat head screw is recommended to fasten it. I suggest using at least 30% infill. Support is not needed. This object

TRENDnet TK-409K KVM Holder for Ikea Ivar

This is a holder for a TRENDnet TK-409K KVM. The holder is hanged on a unit side of the Ikea Ivar shelving system. The TRENDnet TK-409K is a 4

Parametric Bumper Feet

This is a simple OpenSCAD project that generates bumper feet for various objects. It was specifically designed to replace the lost bumper feet of a Falcon Print Trimmer. Printing

Nuvistor Display Stand

This is a display stand for an old electronic part: the Nuvistor which is a type of vacuum tube. It was announced by RCA in 1959. Support is not

ESP8266 Motion Sensor Case

This is a case for a motion sensor based on the ESP8266 and the HC-SR501, a PIR (motion) sensor. Support is not required. This object was designed using Fusion

4 inches x 0.7 inches Label Holder

This is a paper tag holder made out of 4 inches (10.1 cm) x 3 inches (7.6 cm) index cards. They fit an edge of about 1/4 (6.25 mm)

Hanging Buckets for Power Supplies

This kit of objects is two hanging buckets set for a cheap bench power supply. One bucket is 100 mm deep. The other is 50 mm deep. They are

Ikea Bror Caster Holder

This object lets you install casters to a Bror workbench. It is designed for 1-7/8″ (48.5 mm) x 2-9/16″ (65.5 mm) casters. The holes for the bolts are 2-1/8″

Ikea Ivar Vesa 100mm Mount

This is a 100 mm VESA mount designed to be mounted on the Ikea Ivar side units. As shown on the picture, I have used it to mount a

Ivar Side Unit Pin Hook

This is a small pin design to hang stuff on the vertical post of Ikea Ivar side units. The pin is 3mm in diameter, 10 mm long. Support is

Zip Tie Sleeves for the Ivar System

This is a sleeve for Zip Ties. Its main utility is to protect the vertical supports of the Ikea Ivar system when using Zip Ties to attach stuff. They

EN-EL10 Battery Tray

This is two battery tray design for the EN-EL10 batteries. They are used by Nikon for their point and shoot cameras. One of the design holds 6 batteries while

IN-12B Nixie Tube Storage Tray

This is a storage tray designed to hold 12 IN-12 Nixie Tubes. Each compartment is 30.5mm x 20.5mm x 20mm in height. It can be printed without support. This

Stanley Picks and Hooks Pegboard Holder

This is a simple holder for the set of 4 Picks and Hooks made by Stanley. It is designed for the north American pegboard. The holes are 1 inch

Alligator Clip Cable Pegboard Holder (updated)

It can hold up to 20 alligator clip cables. It is designed to be used with a North American pegboard. The distance between the holes is 1 inch (2.54